Magnetie Tools
Hybrid Holder KE-H แม่เหล็กยึดชิ้นงาน
Applicable to systems requiring high speed for robot hands and repeated transport operations in an automated line.
Controller required additionally
KE-5HA
KE-2HA
KE-3HA
• Very little residual holding power permits the speedy release of the workpiece. This enables high-speed operation, for example,an attaching/detaching cycle of 5 to 6 cycle/sec for a lightweight workpiece. • Because it is a permanent electromagnetic type, the holder consumes little power and generates little heat,and thus is suitable for continuous,long period operation. • The holding power is switchable to high, low and off according to normal supply, shutoff and reverse supply of power, respectively. This enables a wide variety of uses.(When at “low,” the holding power is about 1/3 of that at“ high.”) • Powerful rare earth magnet offers high holding power in spite of the small size of the holder.
KE-4HA
KE-6HA
Rust and scratches on the attractive face aff ect the holding power adversely. Repair it periodically. Precautions for use
[mm]
Max. Holding Power 50N (5 kgf) 200N (20 kgf) 400N (40 kgf) 700N (70 kgf) 1000N (100 kgf) 1800N (180 kgf)
Applicable Rectifier
Order No.
Dimensions
Tappad Hole
Voltage
Current
Operating Factor
∅ 20 x 25 ∅ 30 x 40 ∅ 40 x 40 ∅ 50 x 50 ∅ 60 x 60 ∅ 80 x 60
M4 x 0.7 Depth 6 M6 x 1.0 Depth 6 M8 x 1.25 Depth 10 M10 x 1.5 Depth 10
0.07A 0.11A 0.15A
KE-2HA KE-3HA KE-4HA KE-5HA KE-6HA KE-8HA
KR-H1005 KR-H1015 RH-H102B
24 VDC
100% ED
0.2A
0.22A 0.28A
※ For continuous high speed operations, a non-contact rectifi er (RH-H102A) needs to be used. ※ HA type: Cord length 0.3 m (0.2 m for KE-2HA only) ※ The maximum holding power applies to SS400, ground test piece held on the whole area. Test piece thickness : 10 mm for KE-2HA~4HA and 20 mm for KE-5HA~8HA.
Dedicated to electromagnetic/permanent electromagnetic holders Achieve up to 50 percent more compact! Magnetic Controller Model KR ตู้ควบคุมแม่เหล็กยึดชิ้นงาน
A standard type to rectify an input from an AC power source to DC and output it to electromagnetic holders.
• This model comes in various output voltages and output currents selectable according to required capacities. • Compact design.It is also possible to set up in the control panel. • As electric supply code is equipped as standard supply, it canbe used only after it is connected to electro magnet. • As terminal for controlling its outside is equipped as a standard supply, it can be respond to automatic operation. [mm]
KR-T101-6/24
Input
Output
Dimensions
Order No.
Reverse
Applicable Rectifier
Voltage
Fuse Voltage Current
Width Depth Height
KE-1B~4B KE-2R~4RA KE-2D~4E KEP-3C~9C,K5
KE-K310A~ ※ 1 ≀ KE-K515A KE-V306~312 KE-M KE-V510~830
1A 6/24 DC 1A
155
140
95
-
KR-T101-6/24
Single-phase 100 VAC
1A 3A
1A 3A
- -
KR-N101A KR-N103A
KE-5B~9B KE-5E,6E
90 VDC
100
106
77
JSR Entech Catalogue 401 jetco@jet.co.th
※ 1…The rectifi er for KE-1B is KR-T101-6/24A only. The rectifiers for KEP-3C-9C are KR-T101-6/24 and KR-T103-24 only.
jet@jet.co.th
Powered by FlippingBook