Magnetie Tools
Steel Sheet Seperator Standard type แม่เหล็กสำ �หรับแยกแผ่นแม่เหล็ก
Steel sheet separator
Most suitable for removing iron or steel sheets one by one thereby facilitating feeding in automatic steel sheet feeding lines or for separating each iron sheet and for feeding it into a machine (for press or shearing operation). • The highest separating capacity is ensured by two rails on the magnetic polar surface. • Not only steel sheets but also finished pressed workpieces, circular workpieces and irregular workpieces can be separated at fixed intervals by use of several separators. • Compact type with highly efficient ferrite magnet.It can be attached easily to machines. Couple it in comformity with the size,shape and weight of the steel sheets in use. • One set consists of two units. Magnetic force ON/OFF type (by electricity or air cylinder) using the standard type, which can retrieve one by one piece steel plate smoother, is also available.Please consult with us.
KF-30
[mm]
Dimensions
Setting Face
Order No.
B H L 65 87 55.5 45.0 ℓ
No. of Hole
∅ d b 8 40
KF-5B KF-10 KF-20 KF-30 KF-40
56 80
125 210
61.5 51.5 66.5 56.5
8 1
4
127
150
254 72.0 60.0
Steel Sheet Seperator Thin Type แม่เหล็กสำ �หรับแยกแผ่นแม่เหล็ก แบบบาง
Most suitable for installation in narrow spaces because it is thin and compact.
Thin type
• Ultra-thin type 20mm thick. • This separator can be installed in a wide variety of locations, for example, direct installation on a wall face or installation with the L-shaped attachment. • The installing position is vertically abjustable with the L-shaped attachment. • One set consists of two units. (1) DELIVERY OF LARGE IRON SHEET Use it by standing sheets vertically against a wall, etc. You can make good use of the separating force if the Floater is used by standing large sheets in this manner ; thereby minimizing the effect of the weight of the sheets and enhancing the separating force. (2) SEPARATION OF STUCK SHEETS Efficient if you use several Floaters in combination. For separation of large steel sheets or other iron sheets stuck with oil or grease,increase the number of Floaters. (3) SHEETS PILED UP HIGHLY Use a lifter. If steel sheets are piled up high, use a Floater on a lifter (Most adequate level of the Floater is a bit higher than the top sheet). Example of Application
KF-T5A
KF-T20
[mm]
Dimensions
Order No.
D 62
H
b
h
25 50
KF-T5A KF-T10 KF-T20
87
13.5
102
127
[mm]
■ PRINCIPLE OF FLOATER The Floater induces the same magnetic poles in stacked steel sheets to separate the sheets by the repelling force of the same poles. ■ FLOATING DISTANCE When a pair of Floaters are positioned on each side of stacked sheets on the longitudinal sides, the distance the top first sheet is floated from the second sheet is as shown in the table. This distance applies when the Floaters are positioned 50 mm away from the edge of sheets and the initial position of the first sheet is 50 mm below the top end of the Floaters. Note, however, if sheets are warped or oil is sticking to them, the distance will become shorter.
Test steel
Thickness
Size
1.0 1.6 2.0 3.2 14 12 6 - 26 17 9 - 33 26 18 7 34 28 20 10 5 3 2 -
Model
18 14 10 5 150 x 450
KF-5B KF-10 KF-20 KF-30 KF-40 KF-T5A KF-T10 KF-T20
300 x 900
80 x 200
120 10 9 6 160 x 300
Powerful Circular Steel Sheet Seperator แม่เหล็กสำ �หรับแยกแผ่นแม่เหล็ก แบบกลม
An example of usage
Used to separate irregular workpieces (steel sheets) that do not have a straight line of sufficient length.
An example of special fabrication ( )
• The magnetic force can be adjusted by changing the location of the internal magnet. • Small but powerful.
KF-HC0813
[mm]
Thickness D H h PL PW N
Order No. KF-HC0813 KF-HC1218 KF-HC1424
M
76.3 130.0 100 - 60 2 M8 Depth 10 114.3 175.0 140 65 65 4 M8 Depth 12
139.8 235.0 195 80 80
M10 Depth 15
JSR Entech Catalogue 419 jetco@jet.co.th
jet@jet.co.th
Powered by FlippingBook