Testing Instrument
Torque Tester for Electric Driver/ Manual Torque Driver and Wrench เครื่องทดสอบแรงทอร์คสำ �หรับไขควงไฟฟ้า ทอร์คไขควงและประแจปอนด์
■ Specification Show the tester specification below. Order No.
WDI-10HR
WDI-100HR
WDI-250-SJ 0.20~25.00 [N-m]
WDI-10HR-SJ 0.020~1.000 [N-m] kgf-cm/lbf-in/ N-m/cN-m kgf-cm/lbf-in/ mN-m/cN-m
WDI-10HR-OW WDI-10HR-SJ
WDI-10HR-OW 0.20~10.00 [N-m]
0.020~1.000 [N-m] 2.0~999.9 [mN-m] kgf-cm/lbf-in/ N-m/cN-m kgf-cm/lbf-in/ mN-m/cN-m
0.20~10.00 [N-m]
Normal
Range
Hi resolution
2.0~999.9 [mN-m]
0.020 ~ 9.999 [N-m]
0.020 ~ 9.999 [N-m]
Normal
kgf-cm/lbf-in/ N-m/cN-m
kgf-cm/lbf-in/ N-m/cN-m
kgf-cm/lbf-in/ N-m/cN-m
Units
Hi resolution
Accuracy Operating temperature / humidity Sampling rate Data output
±0.5% (If 499 digit or less, ±3 digit.)
15 ~ 35 degrees Celsius, 80%RH or less *Keep a constant temperature while measuring. (Storage temperature 0 ~ 45℃)
1000 data / 1 sec Wired (ASCII format)
Measurement mode Data output Contents Peak hold PP
Measure the peak torque. Measure the firs peak torque
Measurement mode
Peak down
PD
—
Real time output C
Output the torque data every 180 data / 1 sec.
Track
TR
Be used to calibrate mainly.
Memory size Power supply Auto power off
800 data
Ni-MH rechargeable battery (Charge times is about 3 hours) If the tester is not used for 10 minutes. (Releasable)
Socket size
20 / 9.5
Measurement joint AC adaptor Result of calibration, Certification on calibration, Traceability system figure
Accessories (one pieces each)
■ Measurement joint Show the measurement joint which is attached to the product. Order No. Measurement joint Bit
Cube with screw holes
Other
Cube SC-1 SC-1
SC-1 SC-2 SC-3
6mm Hex bit (Ø 4mm, Ø 5mm, 3/16” hex, 1/4” hex)
M3 hex adaptor Grease
SJ-10K
-SJ
M1 M1.2 M1.4
M2.6 M3 M4 M5 M6
M4 M5 M6 M8 M10
WDI-10HR
OW-025 OW-10 SJ-10K
Screw hole
—
—
-OW
M2 M3
M3 hex adaptor M4 hex adaptor Grease
6mm Hex bit (Ø 4mm, Ø 5mm, 3/16” hex, 1/4” hex)
SC-2
-SJ
SJ-50
WDI-100HR
OW-20 OW-60
—
—
SC-2
-OW
Outline figure
6mm hex bit (Ø 4mm, Ø 5mm, 3/16” hex, 1/4” hex) Grease
SJ-50
SC-3
WDI-250 -SJ
SJ-200
17mm socket bit
■ joint Show the SJ joint and OW joint specification below. Joint
SJ joint -SJ
OW joint -OW
SJ-10K
SJ-50
SJ-200
OW-025
OW-10
OW-20 ~ 2 N-
OW-60 ~ 6 N-m
Capacity
~ 1 N-m ~ 5 N-m ~ 20 N-m ~ 0.25 N-m ~ 1 N-m
Recommended measurement range
~ 1 N-m 1 ~ 5 N-m 5 ~ 20 N-m ~ 0.25 N-m 0.25 ~ 1 N-m 1 ~ 2 N-m 2 ~ 6 N-m
Mechanical life
2,500 times
2,500 times
2,500 times Opposite side 17mm M10×(H)35
10,000 times
8,000 times
5,000 times
5,000 times
6mm hexagonal hole on opposite side
Bit fitting part (Use screw top)
M2.6
M3
M4
M6
Dimensions
M8×(H)49
M8×(H)43
Ø 28×(H)35
Ø 32×(H)42.5
Ø 32×(H)42.5
Ø 38×(H)59
JSR Entech Catalogue 556 Pedestal shape
20
20
jet@jet.co.th
jetco@jet.co.th
Powered by FlippingBook