Testing Instrument
Digital Torque Screwdriver ไขควงทอร์คดิจิตอล
■ Specification Model Formula Measuring range
DID-4
0.020~4 N • m 0.20~40 kgf • cm 0.20~35 lbf • in
Accuracy Display
±0.5% (499 or less digit±3digit) The 4 figures digital display of LCD
The measurement direction
CW-CCW (right and left)
peak to peak The highest value of load is hold-displayed.
PP TR
DID-4
track A display also changes with load change. PD peak-down Load catches and displays the moment included in descent from a rise. C Real-time Output Load torque value is outputted every about1/ 160 second. High and low value are measurement within the limits, and can be set up. Five-set preservation is possible. The data number, the maximum, the minimum value, and the average value of memory data are displayed.
Measurement Mode
A success or failure judging function The Maximum, minimum, and the average value Data memory counts auto clear time Setup of count Power supply Charge time / use time Auto-power-off Bit / Socket part Data output
• Possible to display, output and save tightening data. • Built-in screw thread tightening counter. • Integrated display type, easy to use. • For detailed torque management, upper and lower limit settings are possible.
800 data
ASCII format (baud rate 19200) If the set-up time comes, measurement value will be automatically cleared in 0.0~3.0 seconds (0.5s interval). 1 to 99 count (count in a clockwise direction) Ni-MH chargeable battery 1.2V×4cells 800mAh Charge about 3 hour /, continuation about 12-hour use After the neglect during 10 minutes
• Screw tightening work final tightening control.
HEX 6.35
Weight
400g
• Torque accuracy : ±0.5% • Load Direction : Right, Left • Power Supply : Nickel-Metal Hydride Rechargeable Battery (accessory) • 6.35 bit #1, #2 (included) • AC Adapter (included)
Bit #1+, #2+ Bit holder One way bit holder Exclusive charger
Accessories (one piece each)
Result of calibration document Certification on calibration document / Traceability system figure
When outputting data, the cable (USB miniB) is needed.
Option
Digital Torque Screwdriver with connected Display ประแจปอนด์ด้ามไขควงแบบดิจิตอลพร้อมจอแสดงผล The display is separate from the driver. Complete tight- ening control for small screws.
• Accuracy • Display • Measurement modes • Direction of measurement display • Power supply • Battery life operation) • Power off
: ± 1% of indicated value + 1 increment, over the full range : torque reading 4 digit OLCD display
: 1 Peak hold 2. Peak to peak-hold 3. Run
DTDK-EXL
: Automatic CW/CCW changeover, provided with CW/CCW status : two rechargeable "AA" 1.2V batteries and a 100-240V battery charger : Approximately 20 hours with fully charged batteries (continuous
: Auto power-off approximately 3 minutes 40 seconds • Tolerance setting : Automatic judgement capability per the Min/Max settings • Data memory : 100 pieces of data • Output : Printer output (exclusively to a TPK-3), analog output <0 to 1.024 (mid point) to 2.048V >
DTDK-REV
Range (CW/CCW)
Increment Standard Bit (+) Phillips SB Type
Order No.
DTDK-20EXL (New DTDK-20REV) DTDK-50REV
2~20 kgf •c m 0.01 kgf •c m No. 0 , No.1 5~50 kgf •c m 0.01 kgf •c m No. 1 , No.2
DTDK-CN200EXL (New DTDK-CN200REV) 20~200 cN • m 0.1 cN • m No. 0 , No.1 DTDK-CN500EXL (New DTDK-CN500REV) 50~500 cN • m 0.1 cN • m No. 1 , No.2
JSR Entech Catalogue 558
jet@jet.co.th
jetco@jet.co.th
Powered by FlippingBook