Measuring Tools
Offset Caliper เวอร์เนียปากออฟเซ็ท
• The beam-mounted jaw can be adjusted to facilitate measurement of stepped sections and hard-to-get-at workpiece features.
573-601-20
ID 2011207400
Dimensions
536-101
Specifications Metric Order No.
Unit : mm Range Model Range DG J NW 573-601-20 0-150mm 40 10 30 10 95
Digital model
Range
Accuracy ±0.02mm ±0.02mm ±0.02mm ±0.02mm ±0.03mm ±0.03mm
Digital model
0 - 150mm 0 - 150mm 0 - 200mm 0 - 200mm 0 - 300mm 0 - 300mm
573-601-20 573-611-20* 573-602-20 573-612-20* 573-604 573-614*
573-602-20 573-604-20 536-101-20 536-102-20 536-103-20
0-200mm 50 10 38.5 10 95 0-300mm 64 15 51 15 135 0-150mm 40 10 30 10 95 0-200mm 50 10 38.5 10 95 0-300mm 64 15 51 15 135
Analog model
* Without thumb roller Metric Order No.
Analog model
Digital model
Inch/Metric
Range
Accuracy ±0.05mm ±0.05mm ±0.08mm
Range
Accuracy ±.001" ±.001" ±.0015"
Order No. 573-701-20 573-702-20 573-704
0 - 150mm 0 - 200mm 0 - 300mm
536-101 536-102 536-103
0 - 6"/150mm 0 - 8"/200mm 0 - 12"/300mm
Offset Centerline Caliper เวอร์เนียปากออฟเซ็ท
• Specially designed for hole Center-to-Center measurements on the same, or offset, planes.
573-605-20
Specifications Metric Order No.
Digital model
ID 2011207400
Range
Accuracy ±0.03mm ±0.03mm ±0.03mm ±0.03mm ±0.04mm ±0.04mm Accuracy ±0.05mm ±0.05mm ±0.08mm Accuracy ±.0015" ±.0015" ±.0015"
10.1 - 160mm 10.1 - 160mm 10.1 - 210mm 10.1 - 210mm 10.1 - 310mm 10.1 - 310mm
573-605-20 573-615-20* 573-606-20 573-616-20* 573-608 573-618*
536-105
Dimensions
Unit : mm
* Without thumb roller Metric Order No.
Analog model
Range
10.1 - 150mm 10 .1- 200mm 10.1 - 300mm
536-105 536-106 536-107
Digital model
Inch/Metric
Range
W t
Range W t 10-160mm/.4-6.4" 75 3.5 10-210mm/.4-8.4" 75 3.5 10-310mm/.4-12.4" 100 3.8
Range
Order No. 573-705-20 573-706-20 573-708
10-150mm 10-200mm 10-300mm
75 75
3 3
.404 - 6.4"/160mm .404 - 8.4"/210mm .404 - 12.4"/310mm
100 3.8
Centerline Caliper เวอร์เนียวัดเซ็นเตอร์
A
D
E
G
C
H
B
RM30DX
F
O
RM-DX : Specifications
(Unit : mm)
Measuring range Minimum reading Pitch for lower side Pitch for upper side
Minimum hole diameter
Maximum hole diameter
Instrumental error
WeightA B C D E FGH I Θ
Order No.
17~150 9~150 17~200 9~200 17~300 9~300 17~600 9~600 21~1000 11~1000
400g 280 430g 330 500g 410
RM15DX RM20DX RM30DX RM60DX RM100DX
±0.07 ±0.08 ±0.11 ±0.15
50 20 Ø 16
34
76 4
Ø 1.9
Ø 3
Ø 15
31
40 º
0.05
1.16kg 780 85 25
69
116 6
Ø 5
Ø 19 3.15kg 1200 90 32 Ø 20 Ø4 67 35 129 8
JSR Entech Catalogue 53 jetco@jet.co.th
jet@jet.co.th
Powered by FlippingBook