Machine Tools
Minicool สายอ่อนสำ �หรับฉีดนํ้ายาหล่อเย็น
▼ MC3000
For maximum heat dissipation and extended tool life • Strong magnetic base
▼ MC1700
• Separate on/off air and fluid controls • Stainless steel armoured syphon hose and air hose • Nozzle connected via Loc-Line® flexible hose • Simple, inexpensive, rugged • Single spray unit
• Same as MC1700 but with 2 spray units
MINICOOL order no. : Air hose
One spray unit of length (mm)
Two spray unit of length (mm)
Syphon hose
264
334
479
264
334
479
1mm 1mm 2mm 2mm
1mm 2mm 1mm 2mm
MC1700 MC1710 MC1720 MC1730
MC1800 MC1810 MC1820 MC1830
MC2000 MC2010 MC2020 MC2030
MC3000 MC3010 MC3020 MC3030
MC3100 MC3110 MC3120 MC3130
MC3200 MC3210 MC3220 MC3230
Cobra สายอ่อนสำ �หรับฉีดนํ้ายาหล่อเย็น
BASIC COBRA CB2000
Standard Cobra Cooling Kit No.CB2100 แม่เหล็กพร้อมสายอ่อนหยดนํ้าหล่อเย็น (วาล์วไม่มีแม่เหล็ก) Standard Cobra Cooling Kit No.COBRA/M แม่เหล็กพร้อมสายอ่อนหยดนํ้าหล่อเย็น (วาล์วมีแม่เหล็ก)
Includes : Basic Cobra CB20000 Small container CB0146 Mechanical valve SH1000 Magnet DG0036 Arm DG60013 Adaptor DG0129 Nylon tube RM8050
COBRA The COBRA drop ejector is designed to accurately shoot small quan - tities of liquid to distinct targets. An air actuated piston shoots the drops through a flexible hose onto the traget. The drop shots can be automatically timed or manually determined by the user, the amount of liquid in each shot can also be adjusted by a tuning screw at the back of the COBRA all according to the user’s needs. The COBRA is operated by clean air, pressure 3-9 bar. Most liquids and solvents up to 250 cst viscosity can be applied.
COBRA spare parts
Order no.
Banjo screw + washer
MC0232 MC0031 MC0001 MC0030
Banjo fitting Nozzle nut
Washer
Magnetic Type Nozzle Holder สายอ่อนสำ �หรับฉีดนํ้ายาหล่อเย็นพร้อมแม่เหล็ก
Parts for sale !
[mm]
Holding Power
Hose Length
No. of Outlets
Order No.
Base Size Inlet Dia.
NH-P3
250N (25kgf)
∅ 70 x 27
390 420 400 400
1 3 1
NH-P1 NH-P3 NH-M1 NH-M3
500N (50kgf) 48 x 75 x54
∅ 9
245N (25kgf)
∅ 70 x 31
NH-P1
490N (50kgf) 48 x 75 x54 3 ※ limit of air in use : For adjustable hose ( NH-P1,P3 ) : 0.34MPa in Air pressure, 0.2MPa in liquid pressure. For metal Flexible hose : less than 0.6MPa ( limit of flue in use: less than 10 Litter/minute ). However, depending of release angle, there may be a case where posi - tion of a hose can vary by its spouting pressure even though it is within the limit. ※ In such a case, please reduce the fl owing amount. ※ The hose length includes the stainless steel nozzle part (70 mm) at the tip. ※ The holding power applies to SS400, thickness 10 mm and ground surface. ※ Magnet section of NH-P and NH-M is the same,therefore the upper unit is common when mounting.
An example of mounting
NH-M1
NH-M3
Bendable freely !
This holder is designed for holding a nozzle(s) at the end of cutting oil hose on machine tools. This can also be used to remove by injecting cutting liquid chips and particles produced during electric discharging.
JSR Entech Catalogue 864
jet@jet.co.th
jetco@jet.co.th
Powered by FlippingBook