Spray Gun
Low-Pressure Atomization Hand Spray Guns ปืนพ่นสีแรงดันตํ่า
F-110L SERIES
* Paint cup should be ordered separately. *ราคายังไม่รวมกระป๋อง
F110L-G with 4GB-U paint cup
F110L-P
F110L-S with 7SB paint cup
Use of 3D air Exceptional atomization at a very low air cap internal pressure (0.07MPa for pressure & suction type, and 0.05MPa for gravity type). 3D air, whose air flow direction is diagonal, realizes more stable spraying pattern. Higher transfer efficiency, low spattering, and environment-friendly while lowering costs. Lower air pressure design relaizes saving by about 30% in the air consumption and improving by about 10% of transfer efficiency. Furthermore, less spattering paint brings less paint volume and improvement of working environment.
Concept and features of low-pressure atomizing spray guns With a low-pressure atomizing spray gun, the air cap internal pressure is low and the cap air nozzle bore is large, so the airflow velocity drops markedly immediately after the paint is released into the atmosphere. This slows down the atomization rate, reduc - ing splashback and realizing the high transfer efficiency. As a result, paint consumption is reduced by about 15 to 30% compared with a multipurpose spray gun (Meiji product comparison). Reducing spattering and splashback not only creates a better work environ - ment, but also reduces spray booth maintenance. Easy-to-use The use of U-packing in the needle packing place brings free-maitenace, such as no-need retorquing etc. Waterborne compatiblity Stainless steel passage for waterborne compatiblity. Beatiful finishing The use of nickel plating brings improvement of wear and corrosion resistance.
Use of U-packing No need retorquing
Guide
Trigger push
Vernier air hole (3D air) More stable for spraying pattern
Cap packing (Teflon) Improved durability against solvent Moderate tightening
Increased nozzle bore holes from 6 to 8 Improved air flow stability
Tip place ; thin and straight (S type) Tip place ; thin and taper (P type) Improved atomization. Lower air pressure Reduction of dust flying
Spraying pressure
Air pressure inside cap
Maximum effective pattern width mm
Air consumption L/min
Paint spraying volume mL/min
Required compressor output kW
Paint feed system
Nozzle bore mm
Spraying distance mm
Pattern shape
Standard paint cup
Order No.
MPa (PSI) 0.18 (26)
MPa (PSI) 0.07 (10)
0.8 1.0 1.3 1.3 1.5
165 225 320 110 100 115
230 250 270 270 260 270
F110L-P08LP F110L-P10LP F110L-P13LP F110L-S20LS F110L-G13LS F110L-G15LS
Paint pressure feed tanks, diaphragm paint pumps
Pressure
200
345
Tulip 3.7 or more
Suction 2.0 0.15 (22) 0.07 (10)
200 200
265 235
Tulip 3.7 or more 7SB, 10SB-2, 7SLB
1G-2U, 2GD, 4GD,4GF-U, 4GB-U, 4GPA-U, 4G-TA
Gravity
0.12 (17)
0.05 (7)
Tulip 3.7 or more
• Paint viscosity should be 20 seconds for lacquer enamel using a Meiji model V-1 viscosity cup. • Feed pressure should be 0.08MPa for P types. • Air and paint inlet : G1/4
JSR Entech Catalogue 887 jetco@jet.co.th 1MPa = 145.04 Psi
jet@jet.co.th
Powered by FlippingBook